New Holland 275 Square Baler Specs
New Holland Baler Parts Baler Parts for sale at All States Ag Parts. Buy with confidence our new, used, rebuilt parts come with our one year warranty. View updated New Holland Baler specs. Compare size, weight and detailed tech specifications for similar Baler from top manufacturers.
Twine Troubleshooting
- Here at Alma Tractor we stock a large inventory of New Holland 275 Square Baler Parts to help you keep your Square Baler performing at peak efficiency. We carry everything from the Pickup Parts such as Guards, Hardware, Tines, Shear Bolts, to Knotter Parts, such as Bill Hooks, and Gears, to the Dogs, and springs in the Bale Chute.
- NEW HOLLAND SERIAL # BUILD DATE BY YEAR January 2014 Horsepower and quantity built DTD/WK YEAR SERIAL# TO SERIAL# 0.5HP 1.5HP 2HP 3HP 4HP 5HP 1st qtr 15 5133 TO 5182 50 1st qtr 15 5183 TO 5232 50 1st qtr 15 5233 TO 5282 50 1st qtr 15 5283 TO 5332 50 1st qtr 15 5333 TO 5357 25 1st qtr 15 5358 TO 5407 50 2nd qtr 15 5408 TO 5424 17 2nd qtr 15 5425.
- Find used New Holland balers for sale near you. 275 (6) 276 (5) 278 (1) 282 (2). Nice New Holland 570 small square baler, twine tie. New Holland 275 Small Square Baler w/Thrower, Serial # 127201 Field ready, 1972 This unit is located at our Watsontown location.
The knot did not strip off the billhook
There’s a simple knot in twine over the bale but no knot in needle twine
There’s a simple knot in the needle twine
The twine breaks at the knot
Twine in the knot is ragged
There’s a simple knot in twine over the bale but no knot in needle twine
There’s a simple knot in the needle twine
The twine breaks at the knot
Twine in the knot is ragged
There’s no knot in either twine
I’m getting a double bow knot
The twine ends are frayed or uneven
I’m running into other issues
How to pinpoint the problem
I’m getting a double bow knot
The twine ends are frayed or uneven
I’m running into other issues
How to pinpoint the problem
Problem: The knot did not strip off the billhook.
Excessive billhook tension can cause this; decrease tension. Or the billhook may need replacing if it’s rough, worn or bent. Is the knife arm not rubbing the billhook? Adjust or replace it. If the knife arm does not travel far enough, check lobe in cam gear and knife arm roller.
Problem: There’s a simple knot in twine over the bale but no knot in needle twine.
It could be caused by improper twine finger action; adjust to baler manual specifications. Or the needle did not place twine in twine disc, so adjust the needle to specifications and check tensioner at twine box. See if hay dogs are malfunctioning.
Problem: There’s a simple knot in the needle twine.
The twine pulled out of the twine disc. Tighten twine holder and decrease twine box tension.
Problem: The twine breaks at the knot.
Sharp edges may be in the knife arm; smooth the knife arm or replace it. Or you may have too much bale tension; decreasing tension should fix it.
New Holland 275 Square Baler Specs Diagram
Problem: Twine in the knot is ragged.
The twine holder is too tight, which doesn’t allow the billhook to borrow twine when it rotates. To repair, loosen the twine holder.
Problem: There’s no knot in either twine.
Look for a lost or sheared pin in billhook pinion gear. Inspect the trigger roller and trigger pin. Check that trigger is not bent.
Problem: I’m getting a double bow knot.
This means the billhook tension is too light or that the billhook pinion gear has too much wear. Try tightening billhook tension or replacing billhook pinion gear.
Problem: The twine ends are frayed or uneven.
Problem: I’m running into other issues.
Is the hay being baled when it’s too green or wet?
New Holland 275 Square Baler Specs Chart
How to pinpoint the problem.
When you find yourself at the end of your rope, trip the knotter mechanism and run the tying cycle through slowly. Most of the time the problem can be pinpointed when the tying cycle can be viewed in its entirety.